022-27698160
sales@tjql.com.cn
022-27698160
sales@tjql.com.cn
PR3337 HART 7 temperature converter, loop-powered
| Operating temperature | -25°C to +70°C |
| Storage temperature | -40°C to +85°C |
| Calibration temperature | 20…28°C |
| Relative humidity | < 95% RH (non-cond.) |
| Protection degree | IP20 |
| Installation in | Pollution degree 2 & meas. / overvoltage cat. II |
| Dimensions (HxWxD) | 113 x 6.1 x 115 mm |
| Weight approx. | 70 g |
| DIN rail type | DIN EN 60715/35 mm |
| Wire size | 0.13…2.5 mm2 / AWG 26…12 stranded wire |
| Screw terminal torque | 0.5 Nm |
| Vibration | IEC 60068-2-6 |
| 2…25 Hz | ±1.6 mm |
| 25…100 Hz | ±4 g |
Supply |
|
| Supply voltage | 6.2…35 VDC |
| Max. required power | 0.80 W |
| Internal power dissipation | 22 mW…0.8 W |
Isolation voltage |
|
| Isolation voltage, test / working | 2.5 kVAC / 300 VAC (reinforced) |
| Zone 2 / Div. 2 | 250 VAC |
Response time |
|
| HART mode, (0…90%, 100…10%) | 60 ms…60 s, programmable |
| DIP mode, (0…90%, 100…10%) | < 60 ms |
| Voltage drop | 6.2 VDC |
| Signal / noise ratio | Min. 60 dB |
| Programming | DIP switches |
| Signal dynamics, input | 23 bit |
| Signal dynamics, output | 18 bit |
| EMC immunity influence | < ±0.5% of span |
| Extended EMC immunity: NAMUR NE21, A criterion, burst | < ±1% of span |
| Incorrect DIP-switch setting identification | 3.5 mA |
RTD input |
|
| Temperature range, Pt100 | -200…+850°C |
| Accuracy: the greater of | Better than 0.05% of span or 0.1°C |
| Temperature coefficient: the greater of | 0.02°C/°C or ≤ ±0.01%/°C |
| Sensor current | < 150 µA |
| Sensor cable resistance | < 50 Ω per wire |
| Effect of sensor cable resistance (3-/4-wire) | < 0.002 Ω / Ω |
| Sensor error detection | Yes – selectable via DIP-switch |
| Broken sensor detection | > 800 Ω |
| Shorted sensor detection | < 18 Ω |
TC input |
|
| Temperature range, TC J | -100…+1200°C |
| Temperature range, TC K | -180…+1372°C |
| Accuracy: the greater of | Better than 0.05% of span or 0.5°C |
| Temperature coefficient: the greater of | 0.1°C/°C or ≤ ±0.01%/°C |
| Sensor cable resistance | < 5 kΩ per wire |
| Cold junction compensation (CJC): Accuracy @ external Pt100 input | Better than ±0.15°C |
| Cold junction compensation (CJC): Accuracy @ internal CJC | Better than ±2.5°C |
Common output specifications |
|
| Updating time | 10 ms |
Current output |
|
| Programmable signal ranges | 4…20 and 20…4 mA |
| Load (@ current output) | ≤ (Vsupply – 6.2) / 0.023 [Ω] |
| Load stability | ≤ 0.01% of span / 100 Ω |
| Sensor error indication | 3.5 mA or 23 mA / acc. to NAMUR NE43 or OFF |
| HART protocol revisions | HART 7 |
